Calculating Resistor for LEDs

Using a resistor in an LED circuit does not mean that it is possible to eliminate the current-limiting LED driver. The service life of an LED without a driver is reduced by several orders of magnitude. Such a scheme can only be used in products designed to operate for tens or hundreds of hours (an LED flashlight, for example).

Resistor resistance calculator
Molex voltage: 5, 7, 12 Volts
LED voltage: red and yellow - 2 Volts, blue, green and white - 3.2 - 3.6 Volts

 

One LED
Supply voltage:
  V
Nominal supply voltage
of the LED:
  V
Nominal current of the LED:
  mA



Calculated resistance of the resistor:
  Om
Closest value increased by 10%:
 
Calculated resistor power:
  WATTS
Recommended resistor power
when used with this voltage:
  WATTS

 

Sequential LEDs
Supply voltage:
  V
Nominal supply voltage
of the LED:
  V
Nominal current of the LED:
  mA
Number of LEDs:
 



Calculated resistor resistance:
  Om
Closest value increased by 10%:
 
Calculated resistor power:
  WATTS
Recommended resistor power
when used with this voltage:
  WATTS

 

Parallel LEDs
Supply voltage:
  V
Nominal supply voltage
of the LED:
  V
Nominal current of the LED:
  mA
Number of LEDs:
 



Calculated resistor resistance:
  Om
Closest value increased by 10%:
 
Calculated resistor power:
  WATTS
Recommended resistor wattage
when used with this voltage:
  WATTS

 

 

 

 

 

 

 

Coded designation of nominal resistance, tolerance and designation examples

   The coded designation of nominal resistances of resistors consists of three or four characters, including two digits and a letter or three digits and a letter. The code letter is a multiplier indicating the resistance in ohms and determines the position of the decimal point. The coded designation of the permissible deviation consists of a letter of the Latin alphabet (Table 1).

Table 1

Resistance Tolerance Designation examples
Multiplier Code Tolerance,
%
Code Full
designation
Code
1 K(E) ±0.1 V(F) 3.9 Ohm±5% 3R9J
±0.25 C(U) 215 Ohm±2% 215RG
103 К(К) ±0.5 D(D) 1 kOhm±5% 1KOJ
±1 >F(P) 12.4 kOM±1% 12K4F
106 M(M) ±2 G(L) 10 kOhm±5% 10KJ
±5> 2">109 G(G) ±10 К(С) 2,2 МОм±10% 2М2К
±20 М(В) 6,8 ГОм±20% 6G8M
1012 T(T) ±30 N(Ф) 1 ТОм±20% 1ТОМ

 

   Примечание: В скобках указано старое обозначение.

   Цветовая маркировка наносится в виде четырёх или пяти цветных колец. Каждому цвету соответствует определённое цифровое значение (табл. 2). У резисторов с четырмя цветными кольцами первое и второе кольца обозначают величину сопротивления в омах, третье кольцо - множитель, на который необходимо умножить номинальную величину сопротивления, а четвертое кольцо определяет величину допуска в процентах.

 

Цветовая маркировка номинального сопротивления и допуска отечественных резисторов.

Маркировка отечественных резисторов

Рис. 1
Маркировка отечественных резисторов.

Таблица 2

Цвет знака Номинальное сопротивление,
Ом
Допуск,
%
ТКС
[ppm/°C]
Первая
цифра
Вторая
цифра
Третья
цифра
Множитель
Серебристый   10-2 ±10  
Золотистый 10-1 ±5
Черный   0 0 1  
Коричневый 1 1 1 10 ±1 100
Красный 2 2 2 102 ±2 50
Оранжевый 3 3 3 103   15
Желтый 4 4 4 104 25
Зеленый 5 5 5 105 0,5  
Голубой 6 6 6 106 ±0,25 10
Фиолетовый 7 7 7 107 ±0,1 5
Серый 8 8 8 108 ±0,05  
Белый 9 9 9 109   1

 

Цветовая маркировка фирмы "PHILIPS"

   Маркировка осуществляется 4,5 или 6 цветными полосами, несущими информацию о номинале, допуске и температурном коэффициенте сопротивления (ТКС) соответственно. Дополнительную информацию несет цвет корпуса резистора и взаимное расположение полос.

Цветовая маркировка фирмы PHILIPS

Рис. 2
Цветовая маркировка фирмы "PHILIPS"

Таблица 3

Цвет знака Номинальное сопротивление,
Ом
Допуск,
%
ТКС
[ppm/°C]
Первая
цифра
Вторая
цифра
Третья
цифра
Множитель
Серебристый   10-2 ±10  
Золотистый 10-1 ±5
Черный   0 0 1  
Коричневый 1 1 1 10 ±1 100
Красный 2 2 2 102 ±2 50
Оранжевый 3 3 3 103   15
Желтый 4 4 4 104 25
Зеленый 5 5 5 105 0,5  
Голубой 6 6 6 106 ±0,25
Фиолетовый 7 7 7 107 ±0,1
Серый 8 8 8 108  
Белый 9 9 9  

 

Нестандартная цветовая маркировка

   Помимо стандартной цветовой маркировки многие фирмы применяют нестандартную (внутрифирменную) маркировку. Нестандартная маркировка применяется для отличия, например, резисторов,изготовленных по стандартам MIL,от стандартов промышленного и бытового назначения, указывает на огнестойкость и т.д.

Non-standard color marking

Fig. 4
Non-standard color marking.

 

Code marking of domestic resistors

   In accordance with GOST 11076-69 and the requirements of IEC Publications 62 and 115-2, the first 3 or 4 characters carry information about the resistor rating, determined by the base value from the E3...E192 series, and the multiplier. The last symbol carries information about the tolerance, i.e. the accuracy class of the resistor. The requirements of GOST and IEC are almost identical to another standard BS1852 (British Standard).

Code marking

Fig. 5
Code marking.

   In addition to the line defining the resistor rating and tolerance, additional information about the resistor type, its rated power and production date can be applied.

For example:

Additional information about the resistor type

Fig. 6
Additional information about the resistor type.

 

Jumpers and resistors with "zero" resistance

   Many companies produce special Jumper Wires with standardized resistance and diameter (0.6 mm, 0.8 mm) and resistors with "zero" resistance as fuse links or jumpers. Resistors are made in a standard cylindrical case with flexible leads (Zero-Ohm) or in a standard case for surface mounting (Jumper Chip). The actual resistance values ​​of such resistors are in the range of units or tens of milliohms (~ 0.005...0.05 Ohm). In cylindrical cases, marking is done with a black ring in the middle, in cases for surface mounting (0603, 0805, 1206...) marking is usually absent or the code "000" (possibly "0") is applied.

Zero resistance jumpers and resistors

Fig. 7
Jumpers and resistors with zero resistance.

 

Code marking of precision high-stability resistors of the company "PANASONIC"

Code marking of the company PANASONIC

Fig. 8
PANASONIC Code Marking

 

PHILIPS Code Marking

   PHILIPS codes the resistor rating in accordance with generally accepted standards, i.e. the first two or three digits indicate the rating in Ohms, and the last one indicates the number of zeros (multiplier). Depending on the accuracy of the resistor, the rating is coded as 3 or 4 symbols. Differences from the standard encoding may lie in the interpretation of the numbers 7, 8 and 9 in the last symbol.

   The letter R acts as a decimal point or, if it is at the end, indicates a range. A single "0" character indicates a zero-ohm resistor.

Table 4

Last character Resistor value
1 100...976 Ohm
2 1...9.76 kOhm
3 10...9 7.6 kOhm
4 100...976 kOhm
5 1...9.76 MOhm
6 10...68 МОм
7 0,1...0,976 Ом
8 1...9,76 Ом
9 10...97,6 Ом
0 0 Ом
R 1...91 Ом

 

Кодовая маркировка фирмы PHILIPS

Рис. 9
Кодовая маркировка фирмы "PHILIPS"

   Таким образом, если на резисторе вы увидите код 107 — это не 10 с семью нулями (100 МОм). а всего лишь 0,1 Ом.

 

Кодовая маркировка фирмы «BOURNS»

Маркировка 3 цифрами

Рис. 10
А.Маркировка 3 цифрами

   Первые две цифры указывают значения в Ом, последняя — количество нулей. Распространяется на резисторы из ряда Е-24, допусками 1 и 5%, типоразмерами 0603, 0805 и 1206.

Маркировка 4 цифрами

Рис. 11
В.Маркировка 4 цифрами

   Первые три цифры указывают значения в Ом, последняя — количество нулей. Распространяется на резисторы из ряда Е-96, допуском 1%, типоразмерами 0805 и 1206. Буква R играет роль десятичной запятой.

Маркировка 3 символами

Рис. 12
С.Маркировка 3 символами

   Первые два символа — цифры, указывающие значение сопротивления в Ом, взятые из нижеприведенной таблицы 5, последний символ — буква, указывающая значение множителя: S=10-2; R=10-1; А=1; В= 10; С=102; D=103; Е=104; F=105. Распространяется на резисторы из ряда Е-96, допуском 1%. типоразмером 0603.

Таблица 5

Код Значение Код Значение Код Значение Код Значение
01 100 25 178 49 316 73 562
02 102 26 182 50 324 74 576
03 105 27 187 51 332 75 590
04 107 28 191 52 340 76 604
05 110 29 196 53 348 77 619
06 113 30 200 54 357 78 634
07 115 31 205 55 365 79 649
08 118 32 210 56 374 80 665
09 121 33 215 57 383 81 681
10 124 34 221 58 392 82 698
11 127 35 226 59 402 83 715
12 130 36 232 60 412 84 732
13 133 37 237 61 422 85 750
14 137 38 243 62 432 86 768
15 140 39 249 63 442 87 787
16 143 40 255 64 453 88 806
17 147 41 261 65 464 89 825
18 150 42 267 66 475 90 845
19 154 43 274 67 487 91 866
20 158 44 280 68 499 92 887
21 162 45 287 69 511 93 909
22 165 46 294 70 523 94 931
23 169 47 301 71 536 95 953
24 174 48 309 72 549 96 976

   Примечание: Маркировки А и В - стандартные, маркировка С - внутрифирменная.